mimix broadband?s 13.5-17.0 / 27.0-34.0 ghz gaas mmic doubler integrates a gain stage, passive doubler and driver amplifier onto a single device. the xx1007-bd has a self-biased architecture requiring a single positive supply (+5v) only and integrated on-chip bypassing capacitor eliminating the need for external capacitor. this mmic uses mimix broadband?s gaas phemt device model technology, and is based upon electron beam lithography to ensure high repeatability and uniformity. the chip has integrated esd structures for protection and surface passivation to protect and provide a rugged part with backside via holes and gold metallization to allow either a conductive epoxy or eutectic solder die attach process. this device is well suited for millimeter wave point-to-point radio, lmds, satcom and vsat applications. 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler integrated gain, doubler and driver stages self-biased architecture +21.0 dbm output saturated power 40.0 dbc fundamental suppression on-chip esd protection 100% on-wafer rf, dc and output power testing 100% visual inspection to mil-std-883 method 2010 features general description electrical characteristics (ambient temperature t = 25 o c) parameter input frequency range (fin) output frequency range (fout) input return loss (s11) output return loss (s22) fundamental level at the output rf input power (rf pin) output power at 8.0 dbm pin (pout) drain bias voltage (vd) supply current (id1,2,3) (vd=5.0v typical) units ghz ghz db db dbc dbm dbm vdc ma min. 13.5 27.0 - - -28.0 - +16.0 - - typ. - - -8.0 -10.0 -35.0 +8.0 +21.0 +5.0 200 max. 17.0 34.0 - - - - - +5.5 240 absolute maximum ratings supply voltage (vd) supply current (id) gate bias voltage (vg) input power (rf pin) storage temperature (tstg) operating temperature (ta) channel temperature (tch) +6.0 vdc 300 ma +0.3 vdc tbd -65 to +165 o c -55 to mttf table mttf table functional block diagram page 1 of 6 1 (1) channel temperature affects a device's mttf. it is recommended to keep channel temperature as low as possible for maximum life. 1 x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09 x2 rf in vd rf out
doubler measurements page 2 of 6 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09
doubler measurements (cont.) page 3 of 6 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09
xx1007-bd rf out 1 2 3 rf in v d= 5 v bias arrangement physical dimensions page 4 of 6 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09
page 5 of 6 mttf tables (tbd) bias conditions: vd=5.0v, id=200ma these numbers were calculated based on accelerated life test information and thermal model analysis received from the fabricati ng foundry. backplate temperature 55 deg celsius 75 deg celsius 95 deg celsius channel temperature deg celsius deg celsius deg celsius fits e+ e+ e+ mttf hours e+ e+ e+ rth c/w c/w c/w 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09
page 6 of 6 handling and assembly information ordering information caution! - mimix broadband mmic products contain gallium arsenide (gaas) which can be hazardous to the human body and the environment. for safety, observe the following procedures: ? do not ingest. ? do not alter the form of this product into a gas, po wder, or liquid through burning, crushing, or chemical processing as thes e by- products are dangerous to the human body if inhaled, ingested, or swallowed. ? observe government laws and company regulations when discarding this product. this product must be discarded in accordance with methods specified by applicable hazardous waste procedures. life support policy - mimix broadband's products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of mimix broadband. as used herein: (1) life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to aff ect its safety or effectiveness. esd - gallium arsenide (gaas) devices are susceptible to electrostatic and mechanical damage. die are supplied in antistatic containers, which should be opened in cleanroom conditions at an appropriately grounded anti-static workstation. devices need careful handling using correctly designed collets, vacuum pickups or, with care, sharp tweezers. die attachment - gaas products from mimix broadband are 0.100 mm (0.004") thick and have vias through to the backside to enable grounding to the circuit. microstrip substrates should be brought as close to the die as possible. the mounting surface should be clean and flat. if using conductive epoxy, recommended epoxies are tanaka ts3332ld, die mat dm6030hk or dm6030hk-pt cured in a nitrogen atmosphere per manufacturer's cure schedule. apply epoxy sparingly to avoid getting any on to the top surface of the die. an epoxy fillet should be visible around the total die periphery. for additional information please see the mimix "epoxy specifications for bare die" application note. if eutectic mounting is preferred, then a fluxless gold-tin (ausn) preform, appr oximately 0.001 2 thick, placed between the die and the attachment surface should be used. a die bonder that utilizes a heated collet and provides scrubbing action to ensure total wetting to prevent void formation in a nitrogen atmosphere is recommended. the gold-t in eutectic (80% au 20% sn) has a melting point of approximately 280o c ( n ote: gold germanium should be avoided). the work station temperature should be 310o c +/- 10o c. exposure to these extreme temperatures should be kept to minimum. the collet should be heated, and the die pre-heated to avoid excessive thermal shock. avoidance of air bridges and force impact are critical during placement. wire bonding - windows in the surface passivation above the bond pads are provided to allow wire bonding to the die's gold bond pads. the recommended wire bonding procedure uses 0.076 mm x 0.013 mm (0.003" x 0.0005") 99.99% pure gold ribbon with 0.5-2% elongation to minimize rf port bond inductance. gold 0.025 mm (0.001") diameter wedge or ball bonds are acceptable for dc bias connections. aluminum wire should be avoided. thermo-compression bonding is recommended though thermosonic bonding may be used providing the ultrasonic content of the bond is minimized. bond force, time and ultrasonics are all critical parameters . bonds should be made from the bond pads on the die to the package or substrate. all bonds should be as short as possible. rohs compliant parts - all mimix products are rohs compliant unless specifically ordered with tin-lead finish. part number for ordering description xx1007-bd-000v ?v? - vacuum release gel paks xx1007-bd-ev1 xx1007 die evaluation module 13.5-17.0/27.0-34.0 ghz gaas mmic active doubler x1007-bd mimix broadband, inc., 10795 rockley rd., houston, texas 77099 tel: 281.988.4600 fax: 281.988.4615 mimixbroadband.com characteristic data and specifications are subject to change without notice. ? 2009 mimix broadband, inc. export of this item may require appropriate export licensing from the u.s. government. in purchasing these parts, u.s. domestic customers accept their obligation to be compliant with u.s. export laws. january 2009 - rev 14-jan-09
|
